uitrusting
Cable Interface: JST-PH6 to Dupont No Lock
Cable Interface: JST-PH6 to JST-XH6
Plug & Play Interface Cable- Ferrules
50mm Interface cable with
Molex micro-fit 3.0 male connector on one
Plug & Play Interface Cable - JST SMP-02V-BC
50mm Interface cable with
Molex micro-fit 3.0 male connector
Plug & Play Interface Cable - JST VHR-2N
50mm Interface cable with
Molex micro-fit 3.0 male connector
Plug & Play Interface Cable - JST XH-2 With Lock
50mm Interface cable with
Molex micro-fit 3.0
Plug & Play Interface Cable - Molex MX-50-57-9002
50mm Interface cable with
Molex micro-fit 3.0 male connector
The Copperhead Silicone Boot is:
Compatible with Copperhead hotends only.
Made from platinum cured silicone
Gloeidraadgeleider voor 1,75 mm filament die in de onderkant van de QR-, BMG- en V2-extruder past.
3D geprint in zwart ABS / PLA.
Filamentgeleider voor filament van 2,85 / 3,0 mm dat in de onderkant van de QR-, BMG- en V2-extruder past.
3D geprint in zwart ABS / PLA.
Spare part for the Bondtech LGX® Lite
Voron Logo Design
Front housing made of grey Polyamide without
Orbiter style mount to use with the LGX Lite extruder.
Use this set to drop-in replace
Use this mount to install the LGX Lite on a MGN12C or MGN12H carriage.
Laser Sintered
Use this mount to install the LGX Lite on a MGN7C or MGN7H carriage.
Laser Sintered
Use this mount to install the LGX Lite on a MGN9C or MGN9H carriage.
Laser Sintered
Use this mount to attach your Copperhead Groove Mount hotend directly to the LGX Lite.
Laser
Plastic and mounting hardware set
For PERCH setup on CR-10 Smart Strain Gauge plates
Plastic parts made
Plastic and mounting hardware set
For PERCH setup on CR-6 SE and CR-6 Max Strain Gauge
This Convection Shield is only compatible with:
Mosquito Magnum+ Liquid Cooled 1.75mm
Mosquito Magnum+ Liquid
The Mosquito Silicone Boot is:
Made from platinum cured silicone for higher temperature resistance
Thickly
Adapt the Mosquito and Mosquito Magnum hotends to Bondtech QR and BMG extruders using the
Adapt the Mosquito and Mosquito Magnum hotends to Bondtech QR and BMG extruders using the
Prevents plastic adhesion to your nozzles and hotblock
Water-based PTFE nanosuspension
Repels plastic from the outside of
Standardmount for Bondtech QR Extruder
3D printed in ABS, M5 thread inserts.
2x mounting holes for M5,
Silver base thermal paste to improve heat conduction;
Coat your heater and thermistor
Activated alumina desiccant is 10x more powerful than comparable silica gel, and is non-toxic!
Creates
Thermal paste to improve heat conduction;
Coat your heater and thermistor cartridges before
Bondtech aandrijftandwielset van gehard en oppervlaktebeschermd staal.
Precisie cnc-gefreesd.
Deze tandwielset bestaat uit een primair aandrijfwiel, een secundair aandrijfwiel, lagers en een as.
Bondtech aandrijftandwielset van gehard en oppervlaktebeschermd staal.
Precisie cnc-gefreesd.
Deze tandwielset bestaat uit een primair aandrijfwiel, een secundair aandrijfwiel, lagers en een as.
Bondtech aandrijftandwielset van gehard en oppervlaktebeschermd staal.
Precisie cnc-gefreesd.
Deze tandwielset bestaat uit een primair aandrijfwiel, een secundair aandrijfwiel, lagers en een as.
Deze houder voor de BMG-extruder is CNC-gefreesd met nauwkeurige toleranties in 3 mm dik aluminium dat een veilige en stabiele montage van de extruder garandeert.
NEMA17 1,8 graden pannenkoekstappenmotor met hoge resolutie.
Wordt geleverd met een 300 mm JST-XH6-kabel die is gestript zonder een tweede connector.
NEMA17 Pannenkoekstepper met een 150 mm lange niet-verwijderbare gestripte kabel met connector.
NEMA17 gestuurde stepper met een planetaire tandwieloverbrenging.
Geleverd met een 700 mm lange JST-XH6 naar PC2510 kabel met snelkoppelingen.
Zeer nauwkeurige PTFE-buis (Poly Tetra Fluoro Ethyleen)
Binnendiameter: 2,0 mm, buitendiameter: 4,0 mm
Voor 1,75 mm filament.
PTFE-buis met hoge precisie (Poly Tetra Fluoro-ethyleen)
Binnendiameter: 4,0 mm, buitendiameter: 6,0 mm
Voor filament van 3,0 mm
PTFE-buis met hoge precisie (Poly Tetra Fluoro-ethyleen)
Binnendiameter: 3,18 mm, buitendiameter: 6,4 mm
Voor filament van 2,85 / 3,0 mm
Adapter met een geïntegreerde push-fit connector.
CNC-gefreesd in zwart geanodiseerd aluminium, push-fit connector voor 6 mm buis.
Een adapter voor eerdere model N1 / N2-printers met zilverkleurige stappenmotoren om de nieuwe Bondtech DualDirect-extruder aan te sluiten.
Een adapter voor eerdere model N1 / N2-printers met zilverkleurige stappenmotoren om de nieuwe Bondtech SingleDirect Extruder aan te sluiten.
Bevestiging voor Bondtech QR Extruder naar Ultimaker 1.
3D geprint in ABS, M5 schroefdraad inzetstukken in messing.
Adapter met een geïntegreerde push-fit connector.
CNC-gefreesd in zwart geanodiseerd aluminium, push-fit connector voor 4 mm buis.
700 mm
JST-XH4 4-pins connector naar JST-PH6 6-pins connector.
700 mm
PC2510 4-pins connector naar JST-XH6 6-pins connector.