CSMIO-MPG Kit Module & Handwheel for CSMIO/IP Controllers
CSMIO-MPG Kit is a 6-axis solution that provides manual operation of machine axes. This set is made of CSMIO-MPG module and a good quality handwheel. This way you can easily, freely and most of all intuitively move your axes. It’s for those who want to equip their machine professionally. In this not expensive way, you can have a precise tool in your machine for fast configuration of work offsets (G54, G55 …), tool magazine (tool length offset), and for manual operation or fast manual rides.
Technical Data of the Module
Number of axes: 6
Digital inputs (opto-isolated): 10
Digital outputs (opto-isolated): 2
Analog inputs: 2
Supply voltage: 24VDC +/-10%
Power consumption: 5W
Maximum voltage on in/out lines: 30VDC
Maximum load of output line: 30mA
Voltage range of analog inputs: 0-5 VDC
Maximum frequency of encoder signal: 10KHz
Ambient temperature range: 0oC to +60oC
Relative humidity (without condensation): 10% – 95%
Electrical Specification of the Handwheel
Output wave: Square wave
Output signals: A,B, (Line driver output A,A(_),B,B(_), phase)
Current consumption: ≤100mA
Response Frequency: 0~20KHz
Output phase difference: 90° ± 45°
Supply voltage: 5VDC, 12 VDC
Signal level: VH ≥ 85%Vcc, VL ≤ 0.3V
Number of pulses: 100
Output circuit: Open collector NPN, Push pull, Line driver, Voltage
Mechanical Specification of the Handwheel
Signal position: 2kind
Speed without sealing: 500 rmp
Starting torque w/o sealing: ≤2.0x 10-2 ~6.0x 10-2 Nm (+25°C)
Shock resistance: 980m/s2, 6ms, 2 times each on XYZ
Vibration proof: 50m/s2, 10~200Hz, 2 hours each on XYZ
Working life: MTBF≥ 10000h (+25°C, 2000rpm)
Weight: Appr. 740g (incl. 1.5 meter cable)
The CSMIO-MPG Kit includes:
- CSMIO-MPG module
- 1x DB9 ribbon wire
- terminator
- 6-axis JOG handwheel encoder (incl. DB25 plug)
Features:
- Operation stability provided by
> connection of the CSMIO-MPG module with a CSMIO/IP controller through CAN bus.
> The connection of CSMIO-MPG module and handwheel with shielded cable using differential transmission for encoder pulses transfer.
- Easy installation
The connection of CSMIO-MPG Kit is very simple and won’t cause any trouble even to not experienced users. It shouldn’t take more than 5 minutes to run it:
> Fastening the module on a DIN rail
> Placing the DB25 plug of the JOG handwheel in the CSMIO-MPG module socket.
> Connecting the CAN bus with the included DB9 tape
> 24V DC power connection.
> Connecting the E-STOP circuit to terminals E1 and E2 (order of the connections is not important). Terminals E1 and E2 are pins of the handwheel E-STOP button.
- No settings required – CSMIO-MPG in current plugin version for Mach3 (up.to 23.01.2017) is ready to work right after installation and does not need any configuration. In case of Mach4, it will be possible to create your own digital signals configuration and also to use them for purposes not related to MPG module.
- Safety system – CSMIO-MPG module is equipped with hardware E-STOP circuit. After pressing the emergency stop button on the handwheel, the circuit is opened (open circuit), what causes immediate machine stop.
- Solid aluminum housing which dissipates heat and protects electronic circuits very well. Readable led controls on a front panel which make it easier to install and simplify diagnostics in case of any problems with switches and an encoder of a handwheel.
- The sturdy design of handwheel – it was equipped with sturdy and handy housing with excellent quality: switches manual encoder, LED indicating MPG mode work as well as ENABLE and E-STOP buttons. It can serve for many years without any issue even if it’s used regularly.
- Additional features – CSMIO-MPG module has two 0-5V analog inputs that can be used for connection of potentiometers of spindle rotary speed and axis feed rate correction. In case of 4-axis machines, the 5th axis selection switch position (B axis) and 6th position (C axis) may be used for spindle rotary speed and axis feed rate correction. The Correction value is in this case adjusted with the manual handwheel encoder.
- Industry standard – CSMIO-MPG module is adapted to worldwide standards:
> Opto-isolated 24V DC digital outputs
> Opto-isolated 24V DC digital inputs
> The power supply adapted to 24VDC
CSMIO-MPG Kit is recommended to users/companies who:
- retrofit original CNC machines and what to get full functionality by using the handwheel encoder function,
- build new machines and want to raise their utility value implementing solutions previously found in CNC machines of well-known manufacturers.
- build machines with a large working area and are looking for solutions that would allow a machine operator to move away from a control panel and still keeping control over machine axes (in the MPG/JOG mode), axis feed rate, spindle speed, and an emergency stop button.
CSMIO-MPG module can be successfully used in CNC machines of any type, especially recommended for milling and turning machines.
How does it work?
After pressing ENABLE button on a manual handwheel, a CSMIO-MPG module via a CSMIO/IP controller switches Mach3 to MPG mode. After switching Mach3 to MPG mode, the CSMIO-MPG module starts continuous encoder pulses counting and also verifies digital inputs state, to which there are switches connected (of axis selection and step size). All the information are transferred through CAN bus to a CSMIO/IP motion controller, where they are changed into motion trajectory for a selected axis.
Several algorithms are watching over motion trajectory creation. The algorithms’ task is to make axis motion precise and smooth. This way prepared motion trajectory is performed by a servo drive or a stepper drive. At the same moment when an axis is moving the CSMIO/IP motion controller sends current axis position to Mach3 software this way that its axis position DRO shown the current location.
Documentation:
- CSMIO-MPG® v2 JOG Modul (Language: English)
- MPG 6-Axis JOG Handwheel Encoder (Language: English)
